How to Refill Canon Cartirdges PG-30, PG-40, PG-50, CL-31, CL-41, CL-51, CL-52

Refill intructions for Canon Inkjet Cartirdge PG-30, PG-40, PG-50, CL-31, CL-41, CL-51 and CL-52.

1. Remove the label from the top of cartridge
2. Using the drill tool, widen the refill holes for each color.
3. Prepare an area for refilling.
   
4. Attach the needle to syringe and load syringe with 6ml of ink (For color cartridges) position for the 41, 51, 52 cartridges or 20ml for the black 40 and 50 cartridges.
   
5. Insert needle into correct color ink hole (that you created in the vent). Penetrate the sponge inside and be sure the needle does not reach the bottom of cartridge. If the needle penetrates to the bottom of the cartridge, the cartridge will leak and is not salvageable.
6. SLOWLY inject the ink into the cartridge. Stop if the ink begins to well up from the fill hole. Reverse the process and pull about 1ml of ink if it has spilled out the top of the cartridge.
7. Clean off top of cartridge, un-tape the next fill hole and tape over the one just filled. This is so you don’t accidentally contamination other colors.
8. Repeat steps 5, 6, 7, 8 until all colors have been injected.
9. Clean off the top of the cartridge. Place tape over the top of the cartridge so it covers every hole.
10. Use a pin and put a small hole (vent hole) through the tape for each hole on the top of the cartridge. This is important, don’t skip this step. The cartridge must be vented to atmosphere or it will not work.
11. Reinstall the cartidge.

READ MORE - How to Refill Canon Cartirdges PG-30, PG-40, PG-50, CL-31, CL-41, CL-51, CL-52

Resetting Canon Pixma MP450

Resetting canon pixma MP450, this methode reset to rese4t waste ink counter in the printer Canon Pixma MP450. Here how:

1. You must start with printer off and power cable connected to eectric source.
   
2. While press and hold Resume/Cancel button press POWER button- led indicator light in green color.
3. While hold Power button, release Resume/Cancel button.
4. press Resume/Cancel button for 2 times, while hold POWER button, after that, release all button.
5. When led indicator will be lit in GREEN - press Resume/Cancel for 4 times!
6. Turn off the canon pixma mp450 using POWER button.

READ MORE - Resetting Canon Pixma MP450

Reset the Ink Level for Canon MX300

Solution to reset the ink level for Canon MX300. The methode get from printer forum

1. Disconnect the power cable
2. Connect it while holding down the power button
3. With the power button still down, press twice the "Cancel/Stop" red button
4. Release the power button
5. The printes turns into a kind of factory mode...(wait for about 10 seconds, utils it says "Idle")
6. Press the ">" (next to the "OK" button) once."Shipping Mode 3"
7. Press the "OK" button.
8. Press "OK" again for "Without cleaning"
9. A test page will print..
10. Open the cover, like you are about to change the cartridges.
11. Disconnect the power cable again.
12. Take out both cartridges.
13. Close the cover.
14. Connect the power cable once again.
15. Turn the printer on.
16. Now just put the cartridges back...

READ MORE - Reset the Ink Level for Canon MX300

Waste Ink Tank Reset Canon SmartBase MP730

Canon SmartBase MP730 Photo offers you the best available quality in an easy-to-use All-in-One machine guaranteeing high speed and high productivity. The SmartBase MP730 Photo delivers top Canon photo print quality with 4800 x 1200 dpi and 2 picoliter consistent droplet size. The newly developed 'Micro-Nozzles' coupled with Advanced MicroFine Droplet Technology reduce graininess to ensure you of the clearest, crispest photo and text prints available. And, it prints and copies a phenomenal 22 pages per minute in monochrome and 14 pages per minute in color.

Manual Reset procedure for waste ink tank full error in Canon Smartbase MP730 printers:

• Hit the “menu”: Key
• Hit “Copy” Key
• Hit “#” Key
• Scroll thru the menu headings until you come to “Test Mode” - 12th heading
• Hit the “3″ button- this will bring up Eeprom Clear
• Hit “0″ button
• Hit the “Stop” button

READ MORE - Waste Ink Tank Reset Canon SmartBase MP730

Reset Waste Ink Tank Canon MP390 and Canon MP360

Canon MultiPass MP390 Multifunction Review

The Canon MP390 is a great multifunction printer for small homes. For most homes and small businesses, space is a consideration when buying office machines, which is exactly why multifunctions like the MultiPass MP390 from Canon are such a popular choice. By combining printing, copying, scanning, and fax functions into one convenient unit, you can save on valuable desktop space, while taking advantage of all the functionality normally provided by four separate peripherals. The MP390 can also print high-quality color photos directly from compatible cameras and memory cards.

Canon MultiPASS MP360

Canon MultiPASS MP360 is All-in-One (Printer - Copier - Scanner) multifunction Inkjet printer, designed for home and small office.

Manual Reset procedure Waste Ink Tank for Canon MP390 and Canon MP360 Just Follow this step to reset waste ink tank full:

1. Start with printer on, press aadditional functions, Scan, Copy, Scan. Now you should be in service mode.
2. Select Test mode which is like the last available selection
3. Select #8 Printer Test, it will do something here like cleaning or something then it will come up with some other option this is where it gets a bit confusing cause now all it says is like 8-2 or 8-3 push the + or - button until it says 8-3 then hit the select button

• The menu will now say EEPROM Clear
• Select Ink count which is option (0) and press set
• Then press Stop/Reset Followed by the power button and then wait for it to restart.

READ MORE - Reset Waste Ink Tank Canon MP390 and Canon MP360

Reset Canon BJC-5000 and Canon BJC-5100

Manual reset procedure for Canon BJC-5000 and Canon BJC-5100. Reset procedure for the both printer be the same, except for fist steps. For canon BJC5100 do following steps before doing reset procedure.

Canon BJC-5100-Self Test

• Switch Printer off
  
• Hold Power for 1 beep.

The Reset Procedure foe Canon BJC-5000 and BJC-5100

1. Switch off the printers
2. Press and hold RESUME button then press POWER button, The indicator will start blinking.
3. While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
4. When the indicator lights steady GREEN, press RESUME button four (4) times. The indicator should be GREEN.
5. Press Power to set data

Service Test Print

1. Turn off the printer Canon BJC-5000 and BJC-5100
2. Press and hold RESUME then press POWER, The indicator will start blinking.
3. While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
4. When the indicator lights steady GREEN, press RESUME button two (2) times. The indicator should be GREEN.
5. Press the Power button to Print

Nozzle Print

1. Power off printers Canon BJC-5000 and BJC-5100
2. Press and POWER, until heard beeps sound from the printer and release.

Demonstration Print

1. While the printer in ON , Press and hold RESUME button until the printer plays a melody of beeps.

READ MORE - Reset Canon BJC-5000 and Canon BJC-5100

Manual Reset Canon BJC-600, BJC-610, BJC-620, BJC-50, BJC-55, BJC-80, BJC-85, M40, M70, BJ-30 BJC-35v and BJC-70

Some manual reset methode for Old canon printers like Canon BJC-600, BJC-610, BJC-620, BJC-50, BJC-55, BJC-80, BJC-85, M40, M70, BJ-30 BJC-35v, and BJC-70

Manual Reset for Canon BJC-600, BJC-600e, BJC-610, BJC-620

1. Unplug Power Cable from Power Cord
2. Hold POWER and FF and Print Mode buttons
3. While hold the third buttons, Plug the power to Power Cord
4. Release after heard the beeps sound
   

Manual reset methode for Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70

1. Unplug Power Cord
2. Hold POWER and RESUME buttons
3. Plug in Power Cable to Power Cord
4. Release the both buttons after the printers starts up
5. Hold CARTRIDGE and RESUME
6. Press POWERbutton
7. Release all buttons after heard the beeps sound
8. Press CARTRIDGE 16 times
9. Press RESUME
10. Unplug the Power cord again.
    

manual reset procedure for Canon BJ-30 BJC-35v BJC-70 for F14 Error Reset

1. Unplug adapter
   
2. press and Hold POWER button
3. Plug in ADAPTERto the printers
   
4. Release POWER after printer starts
5. Hold FF and MENU and press POWER
6. Release after beeps
7. Press <> Cartridge until 1A is displayed
8. Press ONLINE
9. Press POWER to shut off printer
10. Unplug printer then re-plug printeragain

READ MORE - Manual Reset Canon BJC-600, BJC-610, BJC-620, BJC-50, BJC-55, BJC-80, BJC-85, M40, M70, BJ-30 BJC-35v and BJC-70

Manual Reset Procedure for Printers Canon i850, i950, S600, BJC-1000, BJC-2000, BJC-2100 and S450

Manual Reset Procedure for Printers Canon i850, i950, S600, BJC-1000, BJC-2000, BJC-2100 and S450

Canon i850, i950, S600

1. Start with the printer OFF
2. Hold down RESUME button and then hold down POWERbutton
3. release RESUME button
   
4. press RESUME twice, then release POWER
5. Let green light blink until printer is done futzing

Select function with RESUME press POWER to execute:

presses - light color - function Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter

Canon S450 Printer

1. Swith off Canon S450 printer
   
2. Hold Resume button then press and hold POWER button, the beeper will sound once.
3. Hold POWER and release RESUME
4. Press RESUME twice
5. Release Power button
6. When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
7. Press Power to set data

Canon BJC 1000 Serie

1. Remove Cartridge
2. Unplug the AC Power Cord
3. Hold down the RESUME button
4. Release RESUME after plugging in the AC Power cord.
5. Press the RESUME once within 5 seconds and release the RESUME .
6. Press and HOLD RESUME for two seconds or more and release it.
7. Press and HOLD RESUME for two seconds or more and release it.
8. Unplug AC Power Cord to set data.

Canon BJC-2000 BJC-2100 Serie

1. Remove the Cartridge From Canon BJC-2000 BJC-2100 Printers
   
2. Unplug the AC Power Cord
3. Close Front access panel
4. Hold down the RESUME/RESET button and plug in the power cable to AC power cord
5. Release RESUME/RESET after plugging in the AC Power cord.
6. Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
7. Press and HOLD RESUME/RESET for two seconds or more and release it.
8. Press and HOLD RESUME/RESET for two seconds or more and release it.
9. Unplug AC Power Cord to set data.

READ MORE - Manual Reset Procedure for Printers Canon i850, i950, S600, BJC-1000, BJC-2000, BJC-2100 and S450

Manual Reseting Procedure for Canon S series, I320, 1255, iP1000 and iP1500

Manual resetting procedure for Canon Generic S series, Canon i320, i255 , Canon Pixma iP1000 and iP1500

Canon GENERIC "S" SERIES RESET CODE

Waste Ink Counter Reset.

1. Turn off the printer.
2. Press and hold the RESUME button, then press and hold the POWER button.
3. Release the RESUME button, Next press and release the RESUME button two(2) more times in succession. Note: you are still holding the POWER button). The printer's carriage will "reset" or move momentarily. If the above was properly performed the printer will enter the "Service Mode".
4. Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press.
   

1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)

After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.

Canon PIXMA iP1000

Waste Ink Counter Reset Manual for Service mode

1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

Canon PIXMA iP1500

Waste Ink Counter Reset. Manual for Service mode

1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green
6. Release both buttons

Canon i320, i255
Waste Ink Counter Reset.

Methode 1: Manual Temporary

1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

Methode 2: Manual Temporary

1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

READ MORE - Manual Reseting Procedure for Canon S series, I320, 1255, iP1000 and iP1500

Software Resetter Canon i250, i255, i350 and i355

Software Resetter Canon i250, Canon i255, Canon i350 and Canon i355. This software is one of the software that I has been tested. how to using this software, it's easy. Please following tutorial.

1. Start with your printer Canon i250, Canon i255, Canon i350 or Canon i355 on.
2. Set USB port, equal to the printer.
3. Select printer type in SET DESTINATION sections
4. Click Test Pattern 1
   

Interest to Software Resetter Canon i250, Canon i255, Canon i350 or Canon i355, download the software here.

READ MORE - Software Resetter Canon i250, i255, i350 and i355

Reset Canon Pixma MP140 and Canon MP145

I see two methode to Reset waste ink counter Canon Pixma MP140 or MP145. Manual reset and using software resetter. Reset manual procedure like resetting Resetting Canon MP150. Whereas software resetter for Canon Pixma MP140 and Canon MP145 you can using MPtool Software. to download the software open this link

READ MORE - Reset Canon Pixma MP140 and Canon MP145

Manual Reset for Printer Canon Pixma iP1980

Manual reset for canon pixma iP 1980 it easy and like resetting canon ip 1880.If found problem in your printer canon iP 1980 maybe this methode can be use. This reset manual be used to reset waste ink counter in canon pixma iP 1980.

Here how :

• Turn on your printer Canon Pixma iP1980
• now Press and hold Resume button for two (2) minutes and then release Resume button.
• Turn off the printer and turn on again, the Printer will back to normal again.

READ MORE - Manual Reset for Printer Canon Pixma iP1980

How to Reset Waste Ink Counter Printer Canon Pixma iP 1880

There are some ways to reset waste ink counter in the Canon Pixma iP 1880. Waste Ink counter have full at Canon Pixma iP 1880 marked with The POWER and ALARM lamps flash alternately. If waste Ink have full the printer cannot be used. So, the printer will be able to be used again after reset. You are can use software resetter like GeneralTool or iPTool to reset Canon Pixma iP 1880, you can also do reset manual. Following its way to reset Canon Pixma iP 1880 :

A. Reset Manual.

On reset manual, sometime printer return blinking after turn on again. For reset manual following its way :

• Turn the printer on
  
• Press and hold Resume button for 1-2 minutes
  
• Open the printer cover
  
• Release the catridge and then put catridge again
  
• Close The Cover
  
• Turn Off then Turn On again.

B. Using GeneralTool for canon pixma ip 1800 series

Before using GeneralTool for canon pixma ip 1800, printer driver should have been install correcly in the computer.

Using GeneralTool iP 1800...? why do not use GeneralTool iP 1880. Canon Pixma iP 1880 is canon iP 1800 series. Follow this intruction to reset the printer :

• Download software resetter for canon pixma iP1880 from Here
  
• Before connecting printer to the power suply, press and hold power button then connecting the printer to the power.
  
• While hold the power button press reject button for 2 times then release power button.
  
• Run general tool for canon iP 1880. After the printer know, Click lock release button. ( note : to view locK release menu, min resolution 1024 x 728).
  
• Then select Set Destination to iP1800 (my canon iP 1880 printer is iP1800ASA)
  
• Click MAIN and PLATEN button to reset waste ink counter to zero.
  
• Finally test print by click TEST PATTERN button.

C. Using iPTool software

This is software from Rusia for canon iP series. Using this software give separate experience. this software detect automatically attached printer in the computer. following way reset to use iPTool software :

• Download and ektrak iPtool software, you can download the software from this url : http://www.ipt.nm.ru/
  
• Turn on the printer
  
• Then run iptool software, the software will detect the printer automatically.
  
• To reset waste ink counter to zero click “Reset Main” and “Reset Platen” button.
  
• To view the result do test print.

READ MORE - How to Reset Waste Ink Counter Printer Canon Pixma iP 1880

Canon Pixma iP1200, iP1600, iP2200 Resetter

You have Canon Pixma iP1200, iP2200 or iP1600 and now counter in the printer have full. You require the software resetter Canon Pixma iP1200, iP2200, iP1600 to reset the printer. Software can be used to reset Canon Pixma iP1200, iP1600, iP2200 printers that is iPTool software or you can use GeneralTool software.

iPTool software

To use this software is very easy. Stages usage of this software please follow steps following :

• Turn on the printers.
  
• Download and Run iPTool software (the software will detect automatically the printers). ( iP Tool v. 1.1.5 (189.1 KiB))
• Click reset main and reset platen button to reset waste ink counter.

GeneralTool Canon Pixma iP1200, iP1600, iP2200

Reset use this software is same easy like using iPtools software. To use this software follow these steps :

• Download General Tool for Canon iP1200, iP1600, 2200 Printers. Download GeneralTool
  
• Extract downloaded file the run the software by click GeneralTool.exe.
  
• Select the connected usb port number from usb port then click lock Release then select the applicable model name in set destination setting.
  
• In clear waste ink counter, click main to reset the main waste ink counter or platen to reset the platen waste ink counter.

READ MORE - Canon Pixma iP1200, iP1600, iP2200 Resetter

Reset Waste Ink Counter Canon MP150, MP160, MP170 and MP180

To Reset Waste Ink Counter Canon MP150, MP160, MP170 and MP180, besides using manual reset, there is a way of easier that is using software resetter. Excess use software resetter when resetting Canon MP150, MP160, MP170 and MP180 printer, that is process to reset easier and quicker. Software can be used to reset Canon Pixma MP150, MP160, MP170 and MP180 is MPTOOL software (Download here).

Procedure reset waste ink counter in the printer Canon Pixma MP150, MP160, MP170 and MP180, can follow these steps :

• Before doing reset, ascertaining printer driver have been installed in computer truly and all cables have been attached.
  
• Turn on the printer the run MPTool software. This software will detect automatically the printer. If you install printer truly, hence printer will appear in MPTool windows.
  
• Click Reset Platen and Reset Plate button in the waste ink counter section, this process to reset waste ink counter in the printers Canon MP150, MP160, MP170 and MP180 to zero.
  
• After all process finish,Turn off printer and turn on again.

If you wish to conduct reset manual, the procedure can read here.

READ MORE - Reset Waste Ink Counter Canon MP150, MP160, MP170 and MP180

How to Reset Canon MP 450

To reset canon MP450 any two ways you can do. Fist way, you can reset Canon MP450 use mptool software (this software Can be used on canon MP150, MP160, MP170, MP180, MP450, MP460), second way, you can do reset manual on canon pixma mp450, but I suggest to use fist way.

Why I suggest fist methode ?. if you reset canon MP450 use mptool software you can easier reset printer. Let reset the printer.

Using Mptool Software to reset Canon MP450

• Turn of printer then run mptool software this software automatically detect the printer.
• To reset waste ink counter in the canon MP450 click reset main and reset platen button in the waste ink counter section.
  
• To reset ink level click reset black and reset color in the ink counter section.

Reset manual Canon Pixma MP450 Printers

• Turn off the Printers.
  
• Hold button Resume/Cancel (red triangle in the circle), click on POWER (an indicator light green).
  
• Release the button Resume / Cancel keeping POWER.
  
• Click Resume/Cancel 2 times, keeping POWER, and then release all the buttons.
  
• When the indicator recorded GREEN - click Resume / Cancel 4 times!
  
• Turn off the Canon Pixma MP450 Printers.

MPTool ver 0.96 (165.6 KiB)

READ MORE - How to Reset Canon MP 450

How to Reset Waste Ink Counter Canon Pixma iP 1700 and iP 1300

Reset waste ink counter in the canon printer iP 1300 and iP 1700 can use following methode.

Methode 1 : Reset Using software resetter
If you are reset using software resettet any two software resetter can be used, that is general tools Canon Pixma iP 1300 and iP 1700 or using iPTool (available iPtool ver 1.1.5). following these steps to reset using software resetter :

Resetting Using General Tools

• Download Software Resetter Canon Printers iP1300 and iP1700 Ekstrak the Software ( software resetter canon iP 1300 and iP 1700)
• Go ekstrakded folder and run GeneralTool.exe
• In the USB port select port printer installed
  
• Klik Lock Release release button to open set destination menu. In the set destination menu select you printer type. Any two choice available type, that is iP 1700E and iP 1700J or iP 1300E and iP 1300J. To view your printer type view your printer manual.
  
• In the clear waste ink counter click main and platen button (to reset waste ink counter to zero) Turn off printer and turn on again. Your Canon Pixma iP1700, iP1300 Printers should respond as normal.

Resetting using iP tools

Reset waste ink counter in the Canon iP 1300 and iP 1700 using iPTool software like resetting process in the canon iP 1880

Methode 2 : Reset Manual (Reset Hardware)

• Turn off the Printers Press and hold Resume button and press Power button.
  
• Keep holding down Power button and let Resume button go.
  
• Press Resume button 2 times then let both buttons go. Green lights will flash and then stop blinking.
  
• When green lights are solid, press the Resume button 4 times. Press the Power button and the Canon Pixma iP1700, iP1300 Printers should turn off, if not, press the Power button once more.

READ MORE - How to Reset Waste Ink Counter Canon Pixma iP 1700 and iP 1300